![]() Set: 2 pc Flat Head Machine Screw 8 x 40 mm However we personally would prefer the imperial screws who come with the vise. Take care to make the pilot holes not wider than 6 mm. In case you do not want to bother with imperial taps and you have metric taps at hand we offer this stainless metric screw set which you can use instead of the imperial screws. 1/4 inch or 6.3 mm bit for the pilot hole of the 5/16 inch flat head screw (6 mm bit will do too, is even better in wood!).4.5 and 3 mm bit for the 6 round head wood screws.2-5/8 inch or 65 mm bit for round acetal bushing, round hole alternatively can be made with a router or by hand.Allen key 3/16 inch for the 2 flat head machine screws.5/16-18 tap for the 2 flat head machine screws.You will need, in case you follow the instructions strictly: Also we recommend to read the chapter about tapping holes in wood for machine screws (instructions page 19) as it is not so common to do this in Europe. 230 x 130 x 2 mm as jaw cover for a tenacious, non-marring gripĪssembling notice: Aside from the typical woodworking tools required to build the wood components of the vise and install it, you'll need some tools who not every woodworker in Continental Europe will usually have as they are in imperial (inch) measurements. 2 pieces of leather or crubber (composite material made of cork and rubber) approx.3 Nylon washer for knob attachment (+ one extra).3 Thick washer/spacer for mounting the knob.3 Satin black, wrinkle coated, aluminum knob.2 5/16-18 x 1-1/2 flat head machine screws.6 Round head wood screws for acme nut and acetal bushing.1 Groove pin for attaching handwheel to screw.The hand wheel provides a fast, ergonomic means to adjust the vise and it will never get in your way. Benchcrafted has engineered the Glide to deliver rock-solid workholding without the need for the big lever of a tommy bar. They are also quite unergonomic for rapid adjustments. Otherwise they tend to be clumsy, slow, and they can interfere with your work and your body. T-bar style handles offer one distinct advantage: lots of leverage. BENCHCRAFTED has done away with the traditional "tommy bar" handle in place of a massive iron hand wheel. This vise uses a clever combination of components to deliver incredible clamping force with minimal human effort. The Glide makes holding your work quick, easy, and pleasurable. We highly recommend that you NOT begin installation without all vise hardware in your possession.īENCHCRAFTED Glide Leg Vise Base Hardware The auxiliary wood jaws necessary for iron vises are unnecessary with a leg vise since the vise itself, along with the bench's leg and top, forms the jaws of the vise. Leg vises are also simpler and easier to maintain than iron vises. Leg vises are also more powerful due to the large lever provided by the lower position of the parallel guide. Leg vises are usually more than double this, around 9 inch (228 mm). Iron face vises provide around 4 inch (100 mm) of workable depth from the top of the bench to the screw and guide rods. Without the two guide rods of the iron vise, workpieces can be held right up against the screw, virtually eliminating racking and providing a better overall grip. Leg vises offer greater workholding capabilities than iron vises. Once this "Record-style" iron vise took over, the leg vise slowly disappeared. Leg vises have been very popular before the mass-produced iron face vise became common. A bench vise should work smoothly, easily and quickly. BENCHCRAFTED Glide Crisscross Leg Vise, Tail ViseĪ bench vise should not be a source for frustration, but rather, function as an integral element in the flow of your work, much like a finely-tuned smoothing plane, allowing you to focus on the work itself.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |